Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I am wanting to increase the length of one of my characteristics used when my device is acting as a peripheral. When I increase the size of my characteristic, the softdevice...
Hi,
I needed some figure for my controller selection,
Please if can you tell tthe exact answer it will be very help full,
Using NRF serial example for uart with baud...
Hello,
I have a voltage divider/thermistor circuit where R1 is an NTC thermistor of 100kOhm at 25 ° C. R2 is 100kOhm right now.
I took peripheral_saadc example for SDK15...
Hi all,
I'm testing out and adapting the Thingy Mesh Demo v0.1 , which uses nRF SDK for Mesh v1.0.1 for my internship. I will be testing out a Thingy's Mesh network for...
Hi,
I tried, ble_blinky example on DK, it works well. Also advertising interval 40ms on nrfconnect mobile app,this is consistent with SDK.
Now, i try same example with...
Hello
My name Ilya, am from global company Rosslare -access control. i am a R&D lieder.
I have found that nRF52840 is accepted to my new project - BLE reader.
I want...
Chapter "18.6.1 Power-on reset" of the data sheet describes " A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply...
Hi,
I'm using the BDS Plugin to generate code and I noticed that the code generated for adopted services it's totally different compared to the code into nRF5_SDK_14.2.0_17b948a...
I am trying to use the watchdog interrupt on an NRF52832 but am unable to get it to fire; the watchdog fires, but as far as I can tell not the preceding interrupt. Here is...
Hi,
Does nrfsniffer require a separate dongle? Can I only use my Nordic board with USB cable, sniffer tools & Windows machine? Will that suffice? Well it lists that way...
Does the nrf Mesh Android App/iOS supports Extended Packet Length? Like MTU size > 23 .
I have used Samsung Galaxy 8 but I am not able to provision the Device , even though...
Hello,
I want to use ANT+ communication on the nRF51-dongle that has a PCA10031. I have downloaded the SDK 12.3 to use. I have used some of the BLE examples before that...
Hi all, in new update app NRF Mesh Android, I can send data from Android app to Kit run light switch proxy server in SDK MESH V2.2. But It using generic_on_off_server. So...
My setup is a Android phone, Nordic NRF52, and random BLE devices in the area.
What I want is, the Android NRF-UART app connects to the NRF52 and the NRF52 sends information...
