Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Wondering if there are any example/reference implementations of a bootloader for the nRF51822 that support Device Firmware Update over both UART and BLE? We've got the BLE...
Hi,
I have met problem when apply dfu of nrf52810.
I used dfu sample of 52810 from devzone link: https://devzone.nordicsemi.com/f/nordic-q-a/28471/about-ota-for-nrf52810...
I met a big issue when implement the voltage level switch. I used nRF52832's SPI to communicate with an ECG sensor which has 1.8V SPI. The issue is that, 3.3V signal from...
Having just got the DFU functionality working I got the task of trying to add NFC functionality to the application. The code side was not a problem since I got a c and h file...
According to the BLE 5.0 Specification :
"The Link Layer shall use the primary and secondary advertising channel
indices as specified by the Host, and the used primary...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
We developed a device based on nrf51822.
We use SDK11 and module Device Manager to implement bonding.
We have received feedback from the user, that our deivice was bricked...
Hi,all :
I just want to know how to enable the nrf_log (in the ble example).The version of the sdk is 12.3.0 and the cpu is 51822 .Thank you very much .
On the nRF52810 is it posible to change the gain setting for the SAADC on demand? For example the SAADC is reaching its cap and then the gain is increased so it is posible...
