Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear Developer Zone
I have searched now a lot in the Internet, mostly the say it's possible to reprogramm the Firmware of the nRF51822. I have such a chip and a JLink Debugger...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hi,
What is the minimum current draw required to keep on internal DC/DC regulator in nRF51822?
In S110 SoftDevice profile, is it possible to keep on internal DC/DC regulator...
Hi,
I developed an application for nRF51822 starting from ANCS example.
All works fine but I have current scenario ... starting from a clean situation ...
Execute...
i use demo ble_app_multilink_central and ble_app_multilink_peripheral ,in SDK 8.1.0,but when i use sd_ble_gap_connect (S120 to S110)return NRF_ERROR_INVALID_STATE ,
why?...
I am checking values of my PCB with an nRF51822. VDD = 3V. AVDD ~= 800mV
I was expecting a the AVDD voltage drop to be much less. What should the AVDD voltage be? What...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
We have the bootloader working over serial at UART_BAUDRATE_BAUDRATE_Baud38400. We took a big leap and tried it at UART_BAUDRATE_BAUDRATE_Baud230400 and it failed. We will...
Dfu not working when i try to upload my custom made application second time.
nrf51422 sdk v8.0 and softdevice s110 on pca10028
the steps i used to do dfu are as
1)programed...
Dear all
I have some questions about nRF51822 bluetooth smart beacon kit, I read the User guide, but I can't get information about the following questions:
1、what is the...
I want to change bootloader start address BOOTLOADER_REGION_START to 0x33800 to store user data and DFU. But when I only change BOOTLOADER_REGION_START, my device can't work...
