Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Dear Sir/Madam,
One of our customer is using nRF51822 in the design and Proto has been completed. Customer is looking for the followings.
What all certifications...
Hello:
When I use Android 4.3 to connect nRf51822 AKII board, HEART RATE always show error on discovering services(129, then I can't connect nRf51822 AKII board.
Does...
Hello,
i want to develop open source software for nRF51 but i think the SDK licensing is to restrictive. I cannot use any of provided example code because its permits redistribution...
This is my code snippet
int main(void)
{
uint32_t err_code;
...
// Scheduler
scheduler_init();
// Initialize the SoftDevice handler module.
SOFTDEVICE_HANDLER_INIT...
Hello,
I was working over nordic dev board and found the uart template. but in that, only "data_receive_handler" is mentioned. i want to send data from my dev board to...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC RTC.
It function well when connected to EV board...
I see the "Emulated System OFF...
Hi all,
I'm using the nRF51822-EK (PCA10001) and I'm going to develop a bluetooth cadence (and speed) sensor for MTBs.
I desire low power consumption and i though to put...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO.
...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
I'm trying to build an application on nrf51422 with s310 SDK ver5.2. My application is working fine with Bluetooth and now I want to add ANT service to it so can anyone please...
