When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
hello I'm Mehdi. i work on two NRF24lL01 wireless modules. I have a doubt that this modules can be damaged or not work correctly. because the module don't give external interrupt...
Hi!
I am trying to make basic temperature nodes with nRF2402.
The receiver is nRF24L01 transceiver.
My question for nRF2402; is it possible to send config bits via...
Hello,
Recently I've begun updating to the new SoftDevice and SDK for the nRF51822. When I began debugging my migrated code with the development dongle and Master Control...
I'm looking for a little guidance in figuring out why I get this error now when I call SOFTDEVICE_HANDLER_INIT. It appears that I get the error above at the end of softdevice_handler_init...
Dear nordic guys,I'm developing with nrf51822.
I have one simple question.
I want trying to connection request at the BLE server side to BLE client with previous connected...
I noticed that m_sec_params passed to sd_ble_gap_authenticate(uint16_t conn_handle, ble_gap_sec_params_t const * const p_sec_params) has been declared as a static variable...
Hello
I was trying to make an example program for a Client. And when I was searching for the sd_ble_gap_scan_start function I didn't find it. Altough in the documentation...
I am getting an NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add. This is the 12th characteristic added and follows the same general style of numerous...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
Using these to build a project based on the sample proximity...
Hi,
I just tried to toggle a led when a particular button in the evaluation board (nrf51822) is pressed, i just referred the gpiote sample code and started modifying it...
Hello,
I'm working on the nrf51822 with s110 stack and 5.1 SDK.
Wy functions are not described in the documentation but just enums and data types ?
I'm looking for informations...
I'm wrote a simple test to persist data using pstorage.
But I'm unable to load the stored data.
I'm using gcc and debugging with gdb. So I can see that storage_cb_handler...
Hi,
I am working on a project where there are moving devices. Devices can only move if a wired button is pressed. In fact, for security reasons, there are two buttons connected...
I've been looking at this for the better part of a day and can't seem to pinpoint what I'm doing wrong here. Does anybody want to take a quick peek at this project and tell...
Hi,
I would like to use the PCA10000 dongle hardware and antenna design for my PCB, i got some questions:
1)I have just UART pin outs extra, I would like to reduce the cost...
