Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I noticed today that all the FOTA bundles I used to have on nRFCloud are gone !
Both the ones I added, and the "built in" ones (modem firmware).
Is this a bug...
Good Morning,
I'm currently developing an application for the nRF54L15 where I only need to send single BLE packages, therefore arising the need for keeping track of the...
Hi
I am developing an application where I need to update the BD address for advertising after each disconnection and on reboot. I know Zephyr stack has the API bt_id_reset...
When trying to flash the NRF Bootloader via OpenOCD, i got this error from command line:
nRF52 device has a CTRL-AP dedicated to recover the device from AP lock. A high...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
Hi, I recently started using nrfutil with the deprecation of nRF Command Line Tools. In one of the recent updates the change log lists:
2025-03-24: Version 2.8.4 Added:...
In our project, we referred to the nRF52832 Application Reference Circuit Schematic for QFAA and QFAB QFN48 with internal LDO setup . However, during actual testing, we found...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hello team, We are currently working on a project that used nRF52833-QDAA-B as the MCU chipset. We have followed the circuit configuration 5 for our test case. Our SoC is...
Hi,
MPSL radio notification API has been removed from the nRF Connect SDK v2.6.0.
Is there any alternative way to get radio notifications?
Regards,
Narendra
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
We are developing a project that runs BLE, the Nordic Uart Service, the Nordic Distance Measurement toolikt and Async UART (NCS v2.9.0). The Peripheral device shall advertise...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
I just received a new 54L15DK and was attempting to port a simple 5340 project to it. The first time I attempted to flash it, it _looked_ like it was successful:
[1 0/10...
