Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
Hi all
I am very new to BLE development and I hope that this question was not asked before in another way.
Is this example also available in nRFConnect with another name...
I'm using an nRF52840 microcontroller on an electronic board to read from and write to an S25FL064 flash memory chip. I'm currently using the nRF5 SDK . Before I could read...
I am trying out the Nordic Bluetooth ESL sample example code from the link [ Getting started with bluetooth-esl-and-periodic-advertising-with-responses-pawr ]
Downloaded...
I understand from many posts that the DTS file is ignored when in multi-image (mcuboot enabled) I need to change the partitions to reduce the bootloader from 48K to 32K &...
Hello Nordic Support Team,
I’m currently experiencing issues connecting to my nRF52833 hardware. The device was previously working without problems, but now I’m unable to...
Hello, I am currently developing with NRF52840 and NRF7002 chips. I am running a custom version of the wifi scan sample, using the baremetal library and custom shim file....
Hello,
I wanted to check if it’s possible to use the BLE Mesh light code with other BLE Mesh apps such as ST BLE Mesh, Bluetooth Mesh, or AMCCOM Mesh.
I have tested it...
I am taking some courses from DevAcademy to learn about Zephyr.
I do have some zephyr supported board(s) for the hands-on exercises, but they are STM32 based, not nRF
...
I note that calling:
mpsl_lib_init causes the POWER . INTENSET to be cleared (including the USB interrupts and POF WARN).
My device uses the USB stack, as such, calling...
Hi,
I'm trying to combine Wifi and BLE frequency test on nRF7002 DK. I started with radio_test example on nRF SDK 2.9.1 and toolchain 3.0.2.
I have added CONFIG_NRF70_RADIO_TEST_COMBO...
Hi.
When I made a application with mcuboot on nRF54L15DK.
In order to reduce power consumption, I want to disable serial log(UART).
I added these configuration in the...
Hello,
We have successfully connected a team device and are receiving telemetry from nRF Cloud via MQTT. We subscribe to prod/{team_id}/m/# and receive all team messages...
Hi there.
i start working with nrf54H20 with the hello world example but i encounter to a problem while compiling the example and i dont know what is the reason ?
the...
