I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi all,
I am working with the nRF52 dev kit and the ecg sensor MAX30003. Using MBED to develop firmware.
I am using this library and the example code from maxim ( https...
Hello,
I need to develop an application for nRF51822 that uses SoftDevice 110 v8.0.0 using SDK 12.3 and extend it to use buttonless DFU for the legacy DFU bootloader of...
Hi, support team
I need to realize two-wire uarte receiver(with low power), in the scenario there is no data come from TX in most time, so after receiving the data I need...
SDK: 15.3.0
BOARD: custom nRF52840 pre-product
Hi, I want to implement usb dfu trigger library.
but, faced with a problem.
My project are started from usb cli...
cli_agent_router and multi_sensor example with nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 nrf52840
problem: The coordinator restarts occasionally, and the zed cannot rejoin until...
Hello,
I am trying to configure the SAADC for the NRF52810. I read that I have to enable it via the sdk_config.h. Here I find an entry for:
NRFX_SAADC_ENABLED - nrfx_saadc...
I have two related questions about nRF52 (nrf52832) which I have not been able to pinpoint from the documentation.
Can the 32MHz crystal connection be replaced by...
Hi. I’ve developed a custom device based on nRF9160 and now have a problem of fixing GPS signal. With the same antenna and same conditions sometimes it takes up to 10 minutes...
I've set up a timer which is firing the interrupt correctly. I then set up a second compare and linked it to the PPI to fire the ADC. The idea is to do these a few times per...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
Greetings!
I am using nRF52832 with SDK 16.0.0 and mesh sdk 4.0.0.
Application: light switch client with LPN features added
In one of application, I have to use...
i already done the nrf52840 dongle that already work as beacon when i have tried in nrf beacon apps. i want the same application but now it is transmitting to server/website...
Hi,
I have a low level mcu (128 kbyte flash) connected via UART to the nRF52840.
My current flash usage (text output arm_gcc) is about 256 kbyte + the softdevice.
Since...
