Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,
i would like to point out what i think is a missing dependency in file "include/modem/modem_info.h". At row 187 there is:
but at_param_type is not declared in...
I am going through the steps for building a secure bootloader
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
However I...
Hi,
I am trying to better understand the eSIM provisioning process. I want to verify that the IMSI changes to a local profile after the first registration with the provisioning...
Hi Nordic Devzone readers,
Recently I've picked up a NRF9160DK and have tried to program my own user program onto it. This will consistently fail unless I hold the reset...
Hi,
I am using the BMD340 module from Rigado. The module is connected to a raspberry compute module via UART. The design implemented is the “CLI co-processor design” where...
I have downloaded ADC example to the board nrf51422. I could not figure out how to give analog input and view digital output. please help. Thanks in advance...
To the kind attention of Nordic support team,
I'm using sdk 15.2, I'm working on usb hid composite example, and I modified it to have it scanning a big input keyboard matrix...
Hi,
As we know,we can modify the Mesh params though the config model, but when we actually installing and deploying ,If we want to improve the reliability of the Mesh network...
I try to bring an old Project (2017) back to life and use the new SDK 16
the Code usese BLE_GAP_TIMEOUT_SRC_ADVERTISING, but that is removed in the new SDK version,
what...
51822
SDK11
Can we change the advertise interval after 51822 started? I need to change the interval to lower / higher based on the user phone. For example, if its IOS...
How does Broadcast characteristic property of GATT can allow BLE observers devices to read the data without being connected with the device? Does this mean we share data without...
We recently ported to the nRF52832 and our electrical engineer had to make a couple changes from the reference design due to space constraints. The port has worked well during...
Hi! I'm trying to measure the voltage drop across a custom PCB we're developing. This was done while trying to get a clear sense of the current consumption used by our board...
Hi , I am using nrf52832 and try to implement a high throughput in ble5.1. i interface memory with nrf52832 my task is to read the memory and send the data to the app with...
Hey Nordic Team,
I noticed an issue with the SDK and `nrf_serial.c`
After deactivating all legacy code and removing all references to standard UART I noticed that I was...
