I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Linker script `nrf_common.ld` in nRF5 SDK v16 defines __etext to point to the end of the .text section. It needs to be 4-byte aligned according to comments in `gcc_startup_xxxx...
Hello,
In order to try and implement passkeys, I've implemented my program inside of the glucose app example. The project compiles + runs and crashes sometimes randomly...
Hello everyone, just a quick question.
When routing on the nrf52832 WLCSP package, I noticed that the only inner pin "required" for use is the pin to enable DC/DC (Pin B6...
Hey guys,
I want to create an accurate timer without interrupts. My timer has to be very accurate because I have to send HIGH and LOW signals for 1us. I have read this pos...
Hello.
Currently I am trying to merge the peripheral example ble_uart and saadc examle. My little project is to send potentiometer values over ble.
As of now I have copied...
I have the bmdware.uvprojx project opened in Keil uVision 5 and have the BMD 350 breakout board containing the nRF52832 chip connected to my PC via a J Link debugger (EDU...
Hi all,
Here I am using the nrf52840 in my customized board, in parallel i have nrf52840 dev board.
I am using the twi peripheral to communicate with a i2c based sensor...
Hey,
I am using SDK16 and want to update the bootloader on my NRF52840 from SDK15 with a new one.
I modified the bootloader from SDK16 a little bit. Then I created a Zip...
To the kind attention of Nordic support team,
I have got in here two pictures of flash. The first one it is after installing bootloader and settings, softdevice and application...
Hi,
I am working on a product development that uses an nRF52832 (through a LAIRD BL-652 module).
We have a voltage point (named 5V), that is connected to SIO_28 GPIO through...
Dear,
I used ncs_v1.0.0_joakim to adapt the battery of my thingy91:
I used: battery_monitor_read(); to read the %battery, and it worked well
I just updated new...
I understand correctly that in order to use my private key for my applications, I must first sign an immutable bootloader with this key and upload it to the device?
I used...
Hello there,
It seems the CC310 backend for ChaChaPoly does not allow zero-length data or adata (associated data). I am implementing a protocol that requires this (Wireguard...
I am trying to change the default ATT_MTU size from 23 to 64.
my code uses Ble_nus service and Eddystone_Service.
Eddystone service is in connectable mode and it's where...
Env.: nRF52 customBoard, SES, nRF5_SDK_16.0.0_98a08e2
Hi,
I'am working with ble_app_template example and currently trying, to merge it with the experimental multiperipheral...
