Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I am developing an application using BMaD 300 Eval board nrf52. As a first I want to display device information along with MAC address of BMD 300 I have, in advertising...
Hi,
I loaded bootloader, SoftDevice, and Application using nRFConnect - Programmer. But it doesn't launch the application. It fails at
nrf_bootloader_fw_activate() with...
Hello,
I want to read the values from MPU9250 magnetometer i.e. from AK8963 I wrote a function just like accelerometer and gyroscope shown below:
uint32_t mpu_read_mag...
Hi!
I'm looking for a new Bluetooth module for a controller, and I run across the nRF51. I used to have a module that I controlled from the MCU, but this SoC looks like...
I am trying to use the NRF_LOG system with FreeRTOS. In the case of an ASSERT, I want to be able to:
1) log the location of the assertion
2) flush the logs over RTT
...
I’m using the library pc_ble_driver_py last release 0.14.1, and Nordic DevKit PCA10040. My goal is to set the central IRK value and generate a private resolvable address....
Hi, i am trying to build a ble beacon for personal asset tracking. The one that is like Tile or Trackr. What kind of chipset and program that i should use.
Hello
P airing: Just Works with Bonding: Passkey Entry, Peripheral Displays works for bonding.
I want to make LESC Pairing: Just Works with Bonding. Is it possible? According...
I got a vague "cmake did not complete" error from studio when the sdk was installed at a hgfs mounted disk. It worked ok when the sdl was installed at non-mounted directory...
the gy-80 module which has
1. HMC5883L
2. BMP-085
3. L3G4200D
4.ADXL345
i want to get the x, y, z axis of the sensor's position
which example i have to use and...
I am building a project with CMake, inside nRF SDK for Mesh 3.2.0, which uses the math library:
1. source file includes math.h
2. CMakeLists.txt adds m to target_link_libraries...
There are a lot of missing materials under the topic:
Software Development Kit > Previous versions of nRF5 SDK for Thread and Zigbee > nRF5 SDK for Thread and Zigbee v3...
I'm converting an already working LPN that went into SystemOFF with GPIO wakeup for lowest power consumption.
Now I want to use the RTC2 as a secondary wakeup.
I know...
I am currently developing on the nrf52840DK (Rev 1.1.1) using the mbed os.
To debug on the board using OpenOCD it is necessary to flash the JLink firmware for the board...
Dear Nordic community,
we as a company, have developed products with the nRF52832... currently, we're developing a product with the nRF52840 (because we needed USB).
My...
