hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
To the kind attention of Nordic support team,
I have got legacy nRF24 gzll devices that are supposed to communicate with new nRF52 platform. Sometime it happens that nRF52...
Is board support available for Thingy91 "nRF9160_PCA20035" board in Segger Embedded Studio? I am not seeing "nRF9160_PCA20035" as a supported board under "ncs\zephyr\boards...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi, I using the 15.3 SDK.I want to get the peer's name by filtering Company ID(manu data).The Company ID is in the scan response packet, and peer's name is in the adv data...
Hello!
I would like to use an external antenna with my nrf9160dk to be able to attenuate the signal. But I am unsure about what is needed to make it work.
Is it enough...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
I have a nRF9160 DK and since I am in Germany, we are trying to use the most common LTE band they use here, which are:
Band 1,3,7,20
However, band 7 does not seem available...
When I compile one of the nfr_log modules (e.x. nrf_log_frontend.c) I get the following error.
I do include ../components/softdevice/s132/headers/nfr52 in my User Include...
I have an nRF9160 DK which came with an enclosed eSIM from iBasis, that is supposed to work in most of Europe.
However, after jumping through all the getting started hoops...
Hi All,
Posting this here after a lot of searching and troubleshooting. There have been a lot of similar posts but none actually seems to go into how to implement this in...
I'm successfully printing to the UART1 com port at baud rate 115200, but I have a peripheral I plan to connect that requires 9600. What is the proper way to go about this...
I'm using an NRF52840, SoftDevice s140, FreeRTOS, SDK 15.3.0.
I'm trying to sample my ADC at high speed, >1khz (10-40kHz).
I implemented the logic from the SAADC exaple...
Development environment：
NRF52832
SDK：15.3
SOFTDEVICE：NONE
When testing the FDS module power-off data protection feature, the FDS module is abnormal.
During the...
