Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Dear all,
we would like to use nRF9160 DK as a CAT-M1 reference device for our local test purposes. Usually we use iperf tool for UDP traffic generation. Do you have any...
Hi,
I try to use the nRF52840 as a sniffer. I tried to follow ( https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf ) but I block in the 2.2.5 part.
When I run...
On the NRF52810_PS page, I find UART is exists,
But on the sdk_15.2.0, NRF_UART_Type is disappear at nrf52810.h.
So I can't call any nrf_uart_xxx functions and UART...
Dear All,
I know similar questions have been asked before but I have read around quite a bit and I couldn't find an answer to my specific problem.
I have a ble application...
Hello All,
I am working on the simple advertising example.
I am using SDK_V_15.3 and NRF52 DK board.
I want to create a timer for on / off the advertising repeatedly...
Hello,
I have successfully flashed and run the mqtt-simple example from the nrf samples with the default configuration.
If I run it 10 times in a row, the getaddr with...
Hi.
I struggled to migrate ble blinky example of nrf5 (nrf51422) to nrf51822 using KEIL (SDK5 v12.3) but failed
Here are what I tried.
Firstly, I changed target device...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
HI everyone!
My case:
nRF52832 + toolbox on iOS and Android
I have device pre-programmed using seeger with settings:
Next I want to make DFU update using .zip...
I am trying to receive data from GPS L80 with the nrf52832 board but I am not able to receive anything. I connected the Rx of nrf52832 with GPS and vice versa. I also connected...
Hello, I'm trying to get manufacturer specific data from peripheral, but I don't know how to do this when the peripheral is using extended advertisement with LE Coded PHY...
