hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
Hi
Actually i have a big project and have a problem in the estimation of FLASH and RAM memory for the project
i ma going to implement the mesh SDK with the BLE Stack because...
Hello,
I am working with a custom board with the nrf52832 chip.
I have merged and written the following on the board: SD (s132, 6.1.0) + secure bootloader from the latest...
Hello,
I purchased a nRF52 DK board and sparkfun nrf52832 breakout board , and was successful with blinking the LED on the breakout board.
In order to test if I would...
Hello,
(I am using SDK 15.1 on a linux system)
I will breakdown the question in two parts -
when do we get fatal ? - i know one or two cases for example when softdevice...
Hi.....
i want to transfer the data for every one minute from peripheral device to nrf connect via (phone app).. how to declare in the program and what function to be used...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
Hi,
Just got four 52840 USB dongles, with the intent to evaluate the Nordic BT Mesh. But I've been unable to get even a simple Blinky example programmed on the dongle. I...
Hi all, I've just implemented light switch proxy example and it's working very well. Now, I have three NRF52832 boards, and for instance, I have:
A board in the garden...
Can anybody help me to get out of this error, Error programming through Seggar Embedded Studio,
Additional Load File[0] "E:/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96...
