Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
I am working on a project where we are using a nordic bluetooth chip and connecting it to a RS485 Bus using UART with Baudrate 115200. The messages sent from the Bluetooth...
I want to experiment with BLE Mesh. I have several BLE400's with nrf51822's. I want to use these as mesh nodes. I want to get the nrf52-dk to use as an interface node. Can...
I recently downloaded Segger's Embedded Studio to compare its performance and ease of use with IAR Embedded Workbench. We have a kickstarter version of IAR for ARM which has...
hi,
i am using nrf5 sdk 14.2.0 ble_app_uart example with keil v5 IDE and i am doing coexistence with nrf5 sdk for mesh v 1.0.1 for nrf52832 mcu.
a have done all steps...
I use nRF52840-Preview-DK PCA10056 v0.9.3, SDK 14.1.0.
I would like update bootloader, but i have any problems.
I do these steps
1.eraseall 2.program softdevice 3.load...
May be I just did not fined a good reference manual for the software, but it really frustrating me to try and understand from examples.
Is there some guide which take a...
