I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
On my peripheral I filter the devices connected and refuses them when not bonded.
When a device not bonded tries to connect to the peripheral, it forces the disconnection...
Hi,
I am using nrfsdk11 nrf52 and s132 soft device. In my code,I am doing this in main();
void fs_evt_handler(fs_evt_t const * const evt, fs_ret_t result)
{
if (result...
hello sir,
i am using ble mpu example and it working fine now i want do send some commands from mobile to nrf52832 chip via these commands my application should work.
...
Hi everybody,
I will to use the nRF52832 QFAA for a drone, and I carried out this schematic for this chip.
I have two questions :
For the capacitor C6, which value should...
I'm trying to start my app from the bootloader, which is funcionally basically the same as the one in nRF5_SDK_11.0.0_89a8197.
To start the app I call bootloader_app_start...
Hello.
I use nRF52832 and its dev board, S132 soft device. nRF5 SDK v14.2.0 is the version number.
I want to change some manufacture specific data from mobile app. Like...
I am working on the nrf52840 kit with the ble_app_beacon example, compile and download the code successfully. But I don't know how to test whether the kit is advertising,...
I have my own hardware design with the nRF52840 on it. I more or less copied the whole radio/antenna part from the dev kit reference design. The blinky example works fine...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
