I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi
for some reason I cannot connect any PC terminal to my custom board: I would get consistent NRF_UART0->ERRORSRC = 0x000c or 0x0004 indicating break and/or framing issue...
s132 4.0.2, nRF5 SDK 13. In BLE_GAP_EVT_CONNECTED event handler I try to call sd_ble_gap_data_length_update returns NRF_ERROR_RESOURCES.
I have
#define NRF_BLE_GATT_MAX_MTU_SIZE...
Hi all,
I have some question want to ask.I have about 200 bytes to write to the flash and also I would use the bootloader.
I'm using nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2...
This test program is modified from examples\pin_change_int\main.c, I add the instructions to put the cpu to sleep. And I add nrf_gpio_input_disconnect() for all the pins except...
Hello, I am using pstorage function and I would like to know oppionions of your's what would be the best practise to wait until processor erases the flash memory and would...
Is enable required before configuration? Does toggling NRF_ADC->ENABLE reset the configuration (like it does for the radio?) Is the power to the ADC automatic, so that even...
im using sdk10, I initialiszed ble_stack_init and advertising_init but when starting advertising, it works with BLE_ADV_MODE_FAST but not with BLE_ADV_MODE_SLOW .
why it...
Hallo comunnity
I have a sensor which is working is sending data via BLE and it has a 128 UUID bit service [0x 000000-000000-1000-8000-0080-5F9B34FB]
In order to do...
Hi,
What is available MTU of CoAP and UDP over 6lowpan with IoT SDK ?
In my application, I need to transfer dozens of kb data to ble node over 6lowpan with iot SDK. Do...
Hi, I bonded is ok .But I want to store some data on nrf51822 flash memory using pstorage. What should I do?
Register new or change it :
param.block_size = ALL_CONTEXT_SIZE;...
I have an SPI peripheral that has an odd protocol and in trying to sort out why it was acting up I finally caught a logic trace showing about a 13us break in the SPI data...
Hello,
I am using HID mouse/keyboard examples from SDK to learn creating custom HID device.
Besides using four buttons on EVK to simulate motion action. I would love...
Hi All,
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The...
