Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
2017-03-01T12_28_45.220Z-log.txt Hi,
we experience an issue with the PC-based nRF Connect tool, details are as follows:
we use scan to discover BLE devices,
we...
Hello,
I'm actually working with a custom profile generated with Bluetooth Developer Studio. I'have some difficult to send characteristic with the template.
My setup...
I have a created a bootloader using the bootloader_secure example in SDK 12.1. Using my own public-private key pair I've created two zip files, signed with nrfutil, one with...
I'm modifying 'ble_app_uart' project with custom board.
And also test with Android app that Nordic released.
I'm wondering how to set this connection "bond".
Does Nordic...
Hello all,
I little confused with these two examples as mentioned in my question. Both examples are different and their use case is also different. Can somebody please...
Hi!
Faced such an anomaly. In 2-3% of cases when exchanging PTX device sees a transmission error (the ACK did not come) and device PRX is not see this error.
Is there...
These pins do not work when I connect to nRF51822 module directly..
Like this. I cennceted VDD, SWDIO, SWDCLK and GND to nRF51822 module.
And there are not jumpers to...
Is there any sample code in examples, because am a newbie to this great platform, my objective is to glow an led , when the motion is detected , and also when there is no...
Hi Sir,
I add NUS service into CSCS project base on nRF5_SDK_13 follow the steps below, there was no error occurred after build the project, but it didn't work. Please...
Hello,
I'm trying to set up I2C with an mCube cccelerometer, which has an I2C 7 digit ID of 0x6C and an 8 bit address (write) of 0xD8.
With the code below, I see on...
Hi.
I have a custom board, which I power up via AAA battery through a buck-boost converter. I wan't to measure battery level using on-chip ADC only on requests from master...
Hi there,
I've successfully sent the experimental buttonless dfu app "over the air" but now I am no longer seeing the option to DFU from within Nordic Connect.
Must...
