I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi,
Need help to interface nrf9160 with MSP430.
Making Project where MSP430 will collect the data from ECG sensor and sending to nrf9160 in packet form. nrf9160 will going...
Hi,
Time to time, Our board stuck in QDEC_IRQHandler.
1) In which case QDEC_IRQHandler could occurs?
2) I want system reset from QDEC_IRQHandler automatically.
But...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
During development, I was wondering about advertised packets.
I thought that the advertisement packet...
Hello ,
I have configured one nrf52832 where it sends temperature data over one service's characteristics ( updating the value after every 1 min ) and I am able to see this...
Hello. I am trying to scan for BLE packets and write them out through USBD using nRF5 SDK v15.3.0. I am calling app_usbd_cdc_acm_write() in scan_evt_handler when an event...
If I update prj.conf in a zephyr project, but I'm building with segger and the connect sdk (1.5.1) do I have to do something besides "Build / Rebuild" to get segger to recognize...
Hello Nordic Experts,
I almost finished the development for my mesh project with nRF52840. But I faced some t ricky issues when in mass production. that is the time for...
Hi,
I am using SDK15.3.0 and s132_nrf52_6.1.1_softdevice. (nRF52832)
Getting higher current consumption ( 300uA ) while using the PWM library. ( https://infocenter.nordicsemi...
Hello, everybody.
I bought the nrf5340-dk board and tested the zephyr sample code. The Blinky code is worked. I tried the beacon sample code. But it is not worked. I think...
Hello ,
I have interfaced one NTC sensor with above attached image and below information :
SAADC pin : AIN2 ( NTC - pin )
VCC_nRF voltage = 3.3V
R14 = 51KOhm , 0.5...
Hi Team,
We have some application for using the oversampling code but we are facing some issue in that, we try to use the oversampling example to ours code but its calling...
Dear sir,
When use the template project(Which is in peripheral) for UART tx & rx is not working in without debug, but if i use base project(Like uart) file it is working...
Hello, I've seen some similar questions about resets after downloading firmware, but haven't been able to find the solution to my problem.
I'm using a Minew MS88SF3 NRF52840...
Hi,
We have a working application that allows FOTA when using the SDK 15.2 bootloader. We have recently tried to migrate this to SDK 17.0, and everything works except for...
