When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I just bought a new nRF5340 PDK and wanted to learn it a little bit. I searched on the internet and found very useful information about nRF53 architecture.
But...
Hi,
We have a question regarding a custom implementation of flow control for nrf52840 using SDK16 w/ SoftDevice 7.0.1. Currently, our sensor's primary micro transfers data...
A newbie here. I am studying the simple_timer application in the nRF5_SDK_17.0.0_9d13099 library.
The sample application sets the clock frequency to the timer at 16MHz....
Looking around to develop hardware/software using the RAK4600 module!
RAK4600 (lora Node) uses Lora as its main way to communicate with my Lora server (normal flow).
Consider...
Hello,
I would like to switch on a led of a nrf52840 dongle by pressing the buton of another dongle. I don't know which example to use from SDK 17.0.2 to make a master/slave...
Pairing is rejected after setting,
i)APP_ADV_DURATION to 0
ii)adv. flag in adv. init from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hi,
I tried to implement the UART in my code, based on the UART example code. Just as in the example, I first define the struct with the pin numbers:
The pins in this...
I found there was a example in "nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_uart\arm5_no_packs" .
Is there a applicaion example that when it recv a specific...
Hi
I need to connect to perticular central and i know the central MAC address. So i am using whitelisting in peripheral.
I made below changes in my code in ble_app_uart...
I am trying to use the gzp_dynamic_pairing example in SDK version 16 with Segger Embedded Studio and the PCA10040 dev board. There is no project for SES so I copied what I...
Hi,
I am working on nRF5_SDK_17.0.0_9d13099\examples\peripheral\uart project.
How can I increase the UART buffer? like if I have to receive 100+ bytes data how can I read...
I am using a nRF9160 DK. I'm using a Windows 10 system and setup the SDK using nRF Connect.
I've started to experiment with the serial_lte_modem project -- version 1.3.1...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html links to two pages which cannot be found: https://infocenter.nordicsemi...
Hi,
I am able to transfer data from my custom peripheral device with nRF52840, but data is moving much slower than it should.
I am writing 244 bytes into NUS within...
