Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
i want to store and retrieve data in flash. i followed steps as in the sdk infocenter but i am not getting the interrupt after fs_store(). Actually return value of fs_store...
Hi,
In my current project based on SDK 15.3 and sd140, I am using nrf52840 in both peripheral and central devices. I need to be able to maintain 10 concurrent connections...
Hi i am using the nRF52dk and i am trying to control a bldc can anyone help me to guide in how i can generate a pwm to get a sin wave
best regards Nikolai
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v4.2.0 on my nrf52840 dev board but this gives the following error "boards.h: No such file or...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52805 through a notifying service (SDK16.0.0).
Symptom description
We have app from...
Hello,
I want to use I2C slave on nrf9160, but there is no I2C slave driver implementation.
So I read that instead of this, I can use nrfx twis drivers on nrf9160.
I...
What am I missing when
NRF_SPI_MNGR_DEF(my_spi_mgr, 2560, 0);
causes:
../../../../../../integration/nrfx/legacy/nrf_drv_spi.h:120:37: error: 'NRF_DRV_SPI_INSTANCE_0...
Hey all! I have been using your amazing app timer for a while now but I was wondering if there was a better way to create a low power delay than my current design which goes...
Hello,
My application is the ble_app_uart example of SDK 15.3 extended, and using S112. I'd like to use constant latency mode. Given the app uses S112 for BLE, should I...
Hello,
In demo code of Central_Uart code in nRF Connect SDK, when the scanning is started the scan address (MAC) keeps on changing everytime the code is run. (The central...
Hi, We have a product with nrf24L01p Gazell (LastChangedRevision: 133) that acts as a Host. At the moment I'm trying to pair with this host via a PCA10040 Devkit ( nRF52832...
