I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Cheers!
I've been working to enable TWI0 for our current project, but I've been getting stuck on this compile error:
../SDK/modules/nrfx/drivers/include/nrfx_twi.h:73...
Hi i tested the code with nrf52DK with same code getting 3 analog value from AIN1, AIN2, AIN3 and it worked fine.
But when I use EYSHSNZWZ for my pcb, ADC value was just...
Hi,
On battery powered devices, how is it possible to retain a root key when changing batteries?
The crypto cell has an Always On power domain for retaining device secrets...
Hi guys,
I'm currently using SDK 15.0.0 in Keil MDK and making use of the new NRFX drivers.
Similar to the issue detailed here: https://devzone.nordicsemi.com/f/nordic...
Hi,
In the documentation , you have specified that the nRF Toolbox is supported for mcumgr FOTA.
However, from our tests, it seems that it is not true. Could you please...
Hi,
I'm experimenting with the lwm2m sample on the nRF9160-DK and I enabled the firmware update pull support through a COAP to HTTP proxy :
then simply added :
and the...
Hello peer developers,
This is a general question and dilemma I am dealing with and I wanted to get your opinion.
I am working on a project to implement a short range...
Hi,
Here, i have using two I2C functions EEPROM + SENSOR with nRF52832.
Initially, using ble_app_uart example to read Sensor data using TWIM.
Every minute read Sensor...
I started with ncs/nrf/samples/nrf9160/lte_ble_gateway and have taken parts of ncs/zephyr/samples/subsys/fs/fat_fs to get SD card support
prj.conf
CONFIG_NEWLIB_LIBC...
Here are some of the issues which I am facing in SEGGER Embedded Studio since I updated to nRF Connect SDK v1.3.0:
After I press Debug, Go, a dialogue box opens asking...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
The serial_lte_modem sample is heavily broken. Unlike the AT client sample which simply works with PuTTY out of the box, for the serial_lte_modem you need to configure PuTTY...
Hi all:
I am using sdk 16.0.When put system on idle mode call two times sd_app_evt_wait it works well.But I want to save power,so before enter idle mode,but when I call...
Hi despite trying 3 different approaches (even using the Nordic driver lis2dh12 on a blinky-based project and installing Segger Studio to step/debug into the library code...
I wish to send a message from the nRF Cloud terminal to my device that will land in this branch of nrf/applications/asset_tracker/src/main.c.
} else if ((cmd->channel =...
