Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi all,
I have a Raytac MDBT50Q-DB board which I was programming using an nRF82540-DK. It all used to work fine, but now JLink cannot connect to the Raytac board anymore...
Hello,
I'm using nrf52 DK with SDK 14, to flash a Taiyo Yuden EYSHCNZWZ module ( Module Datasheet ). The flashing is successful, as stated by the output console in Segger...
I am a master student. I am working on a project that uses Bluetooth 5 Beacon Scan.
I bought the nRF52840 dongle to scan the Bluetooth 5 Beacon
I want to scan the Bluetooth...
hello!
I am currently using SDK14.2 (migration to 15.2 WIP) and S132 and on a custom board
requirements - I want to collect data from around 50 (or more) PERIPHERALS...
Hi to all,
i am developing a device with NRF52840 soc and i am using cryptocell IP to create ecc key pair. as you know public key of an ECC alg is a point on spec curve...
Hello All.
I am using the following
SDK Version : nRF5_SDK_15.2.0_9412b96
Segger Studio Version : 4.10
Mesh Version : nrf5_SDK_for_Mesh_v2.2.0_src
I am trying to...
Hi,
I am woking on NRF52840.
OS : Windows
SDK version : 15.0
Dev : Keil IDE.
I am using Timer -2, Compare value method to obtain an interrupt.
The interrupt...
The thing I currently try to implement is to combine two 128-bit services in one app - custom and UART.
I arleady made run them separately - one service at app.
Way they...
Hi All
I have started working on BLE mesh network to control lights.
I have following doubts, please clarify.....
1. To implement mesh network, two options are there...
Hello,
I try to receive encrypted BLE PDUs and to decrypt them on the fly using the radio and ccm peripheral. The radio is configured to trigger the DISABLE task when...
I'm using an nrf52832 development board and am trying to implement a simple toggling of an output pin using a timer and PPI. Below is the code I’m using; however, the pin...
The problem applies to both, nRF5 SDK 15.2 as well as to the nRF5 SDK for Thread and Zigbee 2.0.0.
The Nordic UART Service Client (ble_nus_c.h) defines a struct that contains...
Hello ,
I have been using a NRF51 dongle to record data with a software via BLuetooth Low Energy on my computer
I have been experiencing loos of data between my device...
Hey everyone,
1) can you explain me please what is going on by the Link Establishment Process by the Provisioning: do we set up a connection like by the TCP and after...
