Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello there,
I am working on the iBeacon project.
I want to get the distance to 50m.
Now it detects 5-10 meters.
Soldermask on antenna
Project inspired:
Thanks...
nrfConnect for MacOS won't allow pairing of a BLE peripheral with a nrf51 based dongle.
nrfConnect Version 2.4.0.
dongle PCA 10031 V1.1.0
Mac OS version 10.11.6
A...
Hello, so I have a central and two peripheral cards that each send their counters to the central. What I want to do is compare each of the two counters. But there's a problem...
Can I use the ble_advertising module for the BLE_GAP_PHY_CODED ? Currently my Coded PHY parameters without the module are defined as:
Following the example at NordicPlayground...
Hi all,
I am working on an application where I have an application MCU and my idea was to use nRF52 as a 'modem' over serial API. The device I am making is supposed to be...
When nrf52 board and tablet PC connect, I set the tablet PC in sleep mode. Then how can I wake up tablet PC via pushing a button on nrf52 board. Maybe one event can realize...
Include other files in the ZIP file. Is it possible to include files that are not related to updating in the ZIP file of firmware update? I want to pass the configuration...
Hi all ,
I using sdk12.3 experimental_ble_app_buttonless_dfu project to development , below is my bootloader and project ram setting:
if I don't download the bootloader...
sdk12.3.0 In the ble_app_hrs_rscs_relay example, I added the uart_init function referring to the ble_uart example, but when I execute the APP_UART_FIFO_INIT () function, a...
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
Two nRF51822s were mounted in one board One nRF51822 will be used as a TWI master and the other as a TWI...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
