I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
I think, I found a missing configuration in the QSPI driver for the nrf53 in nrfx_qspi.c. I've stumbled off this, while I was trying to configure MCUboot for the external...
We are working on a Zigbee-based network coordinator using the nRF52840. Our end device is connected to the coordinator, but when the end device leaves the network, it sometimes...
I am trying to understand why my spi_dt_spec doesn't get the right pins when I use the SPI_DT_SPEC_GET ( DT_NODELABEL (kx122_spi), SPI_OP, 0 ); macros. I tried to expand it...
Hi,
I'm using an nRF9160DK v1.0.1 (2021.26) for developing an application using the virtual COM ports for logging. All of a sudden, I saw that my console showed that the...
Hi ,
I am trying to integrate LSM6DSL to BL5340 module(laird connectivity) through SPI but I am getting failed on initialization. I am noob to NRF so could someone please...
Hi all,
I've build my own board with nrf9161 LACA, so for now I've tried to create my own board, for the moment I'm just trying to pilot my 3 leds. I've follow dev academy...
Hi, I'm building an application that will use the nrf9160 as a middle man for a websocket connection that becomes a uart connection on the main processor. Thus I want to receive...
Hello there! I am working on a central-peripheral connection, where sometimes the central is not receiving notification(s) from the peripheral. The central then asks for a...
Completing the nRF Connect SDK Fundamentals in the DevAcademy, I stumbled across this question:
Why is true not a valid answer here? Running gpio_pin_set_dt(&led, true...
Hi,
I was following the beginners tutorial and things were fine till i reached the section to create a project from scratch. I was able to build this project as well.
...
Hello,
I'm curious if there is a dependency to use the same Bluetooth module to perform OTA. If I created my own custom board, would I need to use an identical Bluetooth...
I have followed the procedure given at following url https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/create_application.html and created a application(based...
Hello,
I am working with the Signetik M1-N1 module, which is using the nRF9160 chip, as well as the DEV-M1-N1 breakout board, for evaluation and development:
Since this...
Hi,
I am working on a project that uses nrf52833 as one of I2C master to communicate with few I2C slave devices. Meanwhile there is another MCU (stm32H7) on the same bus...
