I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
Hi,
I've looked around the DevZone for answers to this, and haven't quite seen an answer, so I'm going to post my solutions here.
I am using the secure bootloader from...
Hello
I have a use case of typical 3 key (lock / unlock / alarm) car remote lock key fob implementation. Since I already have nRF82810 / 840 based hardware designs that...
I was checking DFU through serial usb/uart on the following link:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Fsdk_app_serial_dfu_bootloader.html...
I am using nordic nrf52 chip and nordic Soft Device. I observed that power level increases(ramps up ) before finally disconnecting. This behavior is observed when external...
Hello,
I'm working on nRF52832 and i'm porting the SDK15.3.0 (i was currently working with SDK14.2.0) but i'm facing something strange with the function : "ble_stack_init...
hi ... i am using nRF52832 , SDK 15.2 version, using ble_app_uart example , here i want to advertise the device constantly, for that what should i change
i tried to change...
In my project, I typically have 20 central connections to the Nordic device. Occasionally, I need to allow a phone to connect to the device using a peripheral link. When this...
Hello,
From the documentation I read that Softdevice can support maximum 20 BLE concurrent connections. How does Nordic determine this maximum number of 20 and is this arbitrary...
I see the SWD debug port is a 2-wire protocol, SWCLK and SWDIO. My debugger device has two additional pins, SWO and nReset. Are these two pins required to debug and program...
I PURCHASED A SIM OF THE THINGHS MOBILE BECAUSE IBASIC DOES NOT WORK.
I HAVE LAUNCHED ASSET TRACKER AND THE NRF9160 DOES NOT CONNECT. LTE FLASHES IN YELLOW.
IS THERE A...
