Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
In which state are the configured UART pins if the device is held in RESET for nRF52832?
We want to use the UART to communicate with the host without the nRF52832 in certain...
Hi, I have a project where an STM32 controller has the updated binary file for nRF1822 in flash and it will upgrade the firmware on nRF1822 with the serial implementation...
I am trying to add "Softdevice_handler" to project under nRF52 SDK_15.0.3
But i couldn't find "Softdevice_handler" in nRF SDK_15.0.3 and it is there in SDK 11
How to add...
Good afternoon,
The 'sd_ble_gap_device_name_Set' seems to have a limit of 10chars when defining the device name. In principle, it should be 31. Why do I have this limit...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
nRF52840-DK 2pcs, one TX broadcast signal software, one RX software. RX can receive TX.
My nRF52840 product 2pcs, one TX broadcast signal software, one RX software. RX can...
Hi,
I am working with a motion sensor which sends a message when it detects a motion. I am communicating between the nRF52 DK and the sensor via UART. I am able to receive...
Hello,
I am interfacing nRF52840 DK with the MAX30101 sensor. I am able to execute all the TWI transactions necessary by using port 0 pin 27 as SCL and port 0 pin 26 as...
Hi,
As background, what I am trying to implement is continuous uninterrupted SPI master output from the nRF52840, compatible with the MCP4822 two-channel 12-bit DAC. The...
Hi. I have some question.
I'm using Mesh with nRF52832.
How get address after provising?
Is there API function?
1. get or set address -> Unicast address.
2...
Hello,
I am trying to configure a Heart rate sensor MAX30101 with nRF51822. I have initialized the sensor correctly as I can see the LEDs turn on. But when I read data from...
Hi, guys. I'm trying to work with Opus applications using PCA10056 v1.0. In order to play Opus fils using the nRF52840,
do I need audio DAC + audio amplifier to create sound...
Hi,
I am using NRF51822 pca10028 UART ble example ,
I need to give provision to change the name of the device after pairing and reset the device so that it starts advertising...
Hello,
I m bonding a central and a peripheral and saving the bonds into a whitelist i use at each startup. When i delete the bonds on central side, the connection to the...