I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Goodmornig,
I can't compiling the example project ! Do you knows the reason ?
Error ( imagw1 ): C:\Users\utente\Desktop\pc-nrfconnect-rssi-master\fw\src\rssi_uart\sdk...
Hello everyone, I'm trying to run my nrf51 with ADS1298 using SPI. nrf51 is master and ADS1298 is slave.
I configured SPI as
const nrf_drv_spi_config_t spi_config =...
Hi,
I'm trying to implement GPIOs in Mesh 2.0 light switch example and I'm using SDK 15.0. I'm getting undefined reference errors and I know that I have to add legacy GPIOTE...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
Custom app running on a nRF52 devboard. Serial port runs when I use the debugger and continues after I exit the debugger, but does not run from a cold start.
using the...
Hi,
In nRF5 SDK v12.3, the members of nrf_ecb_hal_data_block_t are pointers to non-const data. I was wondering if these indeed need to be non-const for the Softdevice S132...
Hi,
I have a central and peripheral device both are based on nRF52. Central device is running on SDK 12.2.0 and peripheral with SDK 11.0.0. I would like encrypt the communication...
Hello!
We're using SDK 12.3 on our application, and we're aware that the SDK is targeted to be event driven, meaning that our code should be the one keeping track of the...
I am using SDK15 , nRF52832 custom board , keil uVISION 5 , ble_app_beacon example.
I am adding timer to the example.
In below code, when I comment out update_vbatt()...
Good afternoon,
I am facing the following issue:
a client application writes to several characteristics (write with no response) I set in my chip, which trigger the execution...
Hello,
We are porting legacy application to the nrf52840. We are using Keil uVision 5.
The legacy code is using some gcc ideas and extensions so we are forced to use...
Hi ， All
I am using nrf52832 SDK12.3.
When the host runs to the discovery service but has not yet discovered the service，the slave power off. The host can no longer connect...
Hi there.
I Tested Example (secure_dfu_ble_s132_pca10040). Fine work.
but I could not find the example code to transfer the firmware.
I need the code to receive...
Hello,
I'm a little bit confused about max datalength that can be read/written in a characteristic.
See attached, a MTU of 64 bytes is negotiated thus 61 bytes available...
