Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hello,
I was going through the schematic of PCA10040 and I see that the nRF52832 is interfaced to an ATSAM3U2CA-AU. I was under an assumption that nRF52832 itself is a...
We have a custom PCB with the nRF52 MCU.
Our application uses BLE. Thus, we need to program first the SoftDevice. In our case, we are using nRFgo Studio.
Normally, when...
Sorry to ask again, but even after looking for some time at all the marketing material and the forums, it was hard for me to find out what BT 5 features are really supported...
Hi,
I followed the RTT tutorial but When I try to BUILD the project I got this error. What is it?
Error: L6200E: Symbol SEGGER_RTT_WaitKey multiply defined (by segger_rtt_1...
I'm trying to interface bno055 with nrf52 dk (PCA10040). I had written the relevant code for the nrf52 dk and added the same to ble_app_uart code and simple uart code. I'm...
Dear colleagues,
I am trying to erase / program the custom board ( with nRF52832 SoC installed) using nRF52-DK. The setup looks like that:
nRF52-DK Custom / External...
Hello Everyone,
I wants Real Time Clock examples in nRF51 board. Like following link which is implemented on embed microcontroller for nRf51 board.
can any one help...
Hello,
I want to discuss the following code with you:
www.dropbox.com/.../AABddGcZagoqWHnJqfPrpbm9a
In the main file there are init functions for uart and twi and...
Hello,
I am using pca10028 and sdk 12.2. I want to scan the nearby ble devices and want to display the mac address using uart. So which code should I refer or which thread...
I am doing some custom work, and have discovered an odd bug, that I can not seem to figure out.
On the tx radio, I am transmitting a BLE ADV packet with the first 3 bytes...
On nRF52, I see that 100 kHz gives a SCL period of 10 us which is correct but for 250 kHz, I get 8 us instead of expected 4 us. Similarly, for 400 kHz I only see 5 us instead...
I have a case where a module that can perform bit clears in the UICR needs to execute while a Soft Device is present and enabled.
I am aware that any direct flash access...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the soft device to work as s130 for its (simultaneous Central/Peripheral...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
Hi,
we are using nRF52832 and running into memory issues as we add functionality.
It would be great if the '40 was available as a drop in replacement in WLCSP package...
