Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I'm a bit confused about nomenclature and am looking for guidance in how best to implement the needs of my ble app. From the S110 perspective, how are connecting, bonding...
Hi there!
I'm working with secure_bootloader example (SDK 12.1.0) and trying to use i2c communication on bootloader. I'm using the debug code and checking via LOG (uart...
I have built a application with IAR, and made a hex file with Intel extended. It’s works fine with nRFgo Studio. But I got problems with dfu updating from my android. I hope...
Hi. I would like to convert float32_t to uint8_t array for transmission using the ble_nus_string_send function. Can you guys please suggest the method to convert the same...
Hi
To write the some state of the device, I write two bits into the NVM memory. Thus, we get 16 write cycles to one address without erasing. I did this based on the optimization...
Hi all:
I wrote a code to directly read the register 0x43 (MPU_REG_GYRO_XOUT_H)
But the GYRO data I got is wrong
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2...
Hi,
I am trying to implement a Single Bank DFU over Bluetooth for my nRF51822 (256KB / 16KB RAM) using SDK v7.1 and Softdevice 110. I am using GCC to compile the bootloader...
Hi all,
I my application I am interfacing SD card with nrf52 using FATFS file system. I am observing some weird behavior while doing this. I have two SD cards, one of 2GB...
Hi. i'm using nRF52832, SDK13, S132v4 as multi-link peripheral.
As I know, SDK13 supports multi-link peripheral refering to example "experimental_ble_app_multiperipheral...
Hi,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
Actually, I have used nRFgo Studio to flash the softdevice...
Hi
I'm setting up a firmware based on the DTM example to perform certification tests.
In the DTM example firmware I see that there is a VENDOR_SPECIFIC command option...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
