Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi.
Currently, the following results came out in the power-saving support .
■Our App
・Advertising Status
1.04mA ~ 1.13mA
・Connection Status ★1
1.044 ~...
Hi.
After stopping the Advertising,I measured the current.
For some reason, usually it is consumes about 1.1mA.
Because too large current consumption,
As a result...
Hi I using nRF51822, and want to know about the Nordic driver support LMP feature
Do you have any document about driver support? Or any software development document except...
Hello, I need to create a high resolution/high frequency PWM signal on the nRF51822. I have been using the new PWM library in the 8.1 SDK and can't quite get there.
From...
Hello. After a couple of s210 and s310 projects, I am attempting an s120 project. I built a client SDK but sd_nvic_EnableIRQ returns error code 0x2009 or NRF_ERROR_SOC_PPI_INVALID_GROUP...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
