According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I used binwalk to analyze the zephyr.signed.encrypted.bin file generated by the routine mcuboot_with_encryption. I found that the firmware was not encrypted but merely compressed...
We have a peripheral device that maintains a PAwR sync (as a syncer/responder), connects to another peripheral in a central role, and also accepts connections from a central...
I tried writing read and write code for sEMMC based on information obtained from an AI assistant. The resulting code is shown below:
As you can see, the block address...
I used an oscilloscope to check the waveform and found that only the clock and IO0 had waveforms. I am using this interface to send data:
nrfx_err_t nrfx_qspi_write (...
This is just simple feedback on the nRF Connect Toolchain Manager v0.9.2.
The download speeds when installing an SDK are terribly slow. On a 1Gb /s connection my PC was...
Hi Nordic team,
We are currently migrating our project from nRF Connect SDK v3.1.1 to v3.2.4 on the nRF9160 .
Our application was working without issues on v3.1.1. After...
I am working with:
NCS Version: 2.6.1 (SoftDevice Controller)
Hardware: nRF52x Platform
on a custom board (nRF52 series) and I'm trying to achieve a "Headphones...
Good morning,
It has been implemented a sleep mode to save battery when the board is not used.
To do that we follow the documentation and implemented the SystemOn mode...
Dear:
I am using SDK12.3 with S132 write application using BLE+DFU+UART+I2C, The device connects and communicates with mobile devices through our own application(ONF Link...
I understand that in %XSYSTEMMODE the flags are not just for fun so practically what are points to do not enable the GNSS always even if I do not use it? I do not care on...
HI
I am currently doing secondary development based on the periodic_adv_conn sample project, using NCS 3.2.1 and the nRF54L15 chip,PHY CODE S8.
I want to add a function...
Hi， We use 52840 based on NCS3.2.4，add UART1 to blinky example because I need to use UART0 to log and UART1 to communicate with MCU for our application. The UART1 could send...
Hello,
I am trying to write data into an external flash memory using a custom board (NRF52840-QFAA). The external flash is the W25Q256JVEIQ. I get a fs_write (-22) error...
As reported on Discord, there is a bug in drivers/serial/uart_nrfx_uarte.c that leads to failing compilation:
zephyr/drivers/serial/uart_nrfx_uarte.c: In function 'cbwt_uarte_async_init...
