Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
Hi.
I have some trouble to use a sensor based on JDY-23 module with nrf52832 dk
(JDY-23 datasheet : ://fcc.report/FCC-ID/2AXM8-JDY-23/4936741.pdf )
We tried to connect...
Hi,
Is LLPM over the air compatible between nRF52840 and nRF5340 devices?
I am aware that LLPM is not fully supported yet on nRF5340. Also, any update on the LLPM support...
We are hearing solder bridge issues on the NRF52832-QFAA:
"Due to the high thickness of the copper layer and small lead spacing on the component, the boardshops are not...
I am working on customizing the DFU bootloader (to add encryption). When attempting to use the instruction trace in Ozone to debug, I see a lot of nonsense. One example is...
I've been analyzing various nRF52 devices and noticed that there is an inconsistency with vendors using Legacy DFU and Secure DFU. Or in other words, there doesn't seem to...
Hi everyone,
I am experimenting with the QSPI example provided with SDK 16. I am facing issues when I try to erase memory blocks or the entire chip.
1. First of all I...
Hi, what I want to achieve is to do a list of devices that I may want to connect to, choose one and pair/bond it (at this point, the central is paired with only one peripheral...
Hello DevZone,
I have recently received the nRF52840 Dongle and I'm able to program it properly with the nRFConnect App. However, when I try to program it with the nRF52832...
Hello
I am using SDK v17.0.2 and nrf52DK. I am trying to encrypt and output the saadc value of the sensor.
I used the AES CTR example almost exactly the same.
And I...
