I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I have a huge issue with NRF52832 and DFU on custom board. I have a custom characteristic in my application to switch to DFU after proper PIN typing. Then I call this...
Hi All,
I'm trying send custom board(nrf52832) sensor data to DK by ble uart and multilink.
When I build the code in Keil. I got the message:
..\..\..\main.c(544): error...
I am using the light bulb example and connecting to the Zigbee2MQTT. The Z2M is running on a docker with logs level set to debug.
So from the light bulb example, how can...
Hi. So, pretty sure I've got the firmware installed right and plugging the dongle in creates a "/dev/tty.usbmodem1101" entry. Problem is I have a crash in Python:
This...
I am going to send a sequence of notifications and the documentation provides this information
The API functions that may consume an application packet depending on the...
Hello,
I am using the nRF52811 for my project. I am in the layout design phase...almost completed and I need some clarifications before I launch the first Proto.
I don...
I have found a lot of people having problems debugging with the SD enabled, but we are not using any BLE atm. We are just using the softdevice for OTA updates. But this is...
hi support team,
i just want to confirm, for mesh SDK, i can only find "APP_UNACK_MSG_REPEAT_COUNT" to increase message repeat count, for ACK message, i can't find any...
Hello NRF Team,
We are using nrf51822 chip for one of our product. Currently, we are using a GPIO connected to user button to Turn On the device from system off sleep mode...
Hi,
I have an issue with broadcasting Eddystone TLM + iBeacon, my project is based ble_app_eddystone example and nRF5_SDK_17.0.0_9d13099, SOC is nRF52832.
Beacon advertise...
Hello,
I am developing a circuit which is based on nRF52820. I got the boards manufactured but they are not functioning properly for some reason.
Following are the errors...
CHIP: nRF52840
SDK: Thread and Zigbee 4.1.0
SD: s140 using multiprotocol
Hi, I have developed zigbee end device.
The communication with the coordinator has be done...
Hi,
I'm using pc-ble-driver and a PCA10040 devkit. I'm having issues with using sd_ble_gap_data_length_update.
First, my configuration has ATT_MTU set to 247:
Then...
Hi! I've read a bit about the limitation of write/read cycles with the nRF52840. I the ~10,000 write/read cycles limit means after this many erases, the flash is no longer...
