Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while，
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...
Hi,
I do have customized services in my project to implement,I think it would be easy if we seperate service related functions from main to add services in further.To serve...
Hello, There were some problems while making Bluetooth packet readers.
Packet sent to another device cannot be read in BLE_GAP_EVT_ADV_REPORT.
Is there any way I can read...
Hi. I'm working with the nrf52832 chip, and had a few high level questions I wanted outside opinions on
1) I have a lot of trouble connecting to my BLE device. I frequently...
Hi Team,
We are going to use the NRF52832 soc with S132 Soft Device and SDK Version is 16 for our project purpose, we have some queries on this soc along with these SD and...
Dear,
I am struggle a problem in mesh communication.
Mesh SDK 4.1.0
I used dimmer example.
Two nodes can communicate and work perfectly fine, only if they are in communication...
Hi,
I used DK board for quite a while with a single certificate, which has been generated and written by nrf_modem functions.
Recently I upgraded the modem to firmware...
Compiler error message: Development environment: keil5 DeviceFamilPack: v8.32.1 SDK: nRFSDK160098a08e2(v16.0.0) I can't compile successfully using the SDK example, how can...
