I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
nRF54L replaces the RTCs from nRF52 with the GRTC. GRTC only have a single CC which is able to generate repeating events with the use of the CC0 interval register. I would...
Hi,
While completing the nRF54L Series Express course, I noted that USB support is not provided by the bare-metal SDK.
I wanted to check if adding support for this is...
I tried to build the Blinky sample description in nrf sdk fundamental academy training without success.
Error occur during build at B0n stage:
error: 'struct shell_ctx...
## Summary Setting `CONFIG_MEMFAULT_NCS_INTERNAL_FLASH_BACKED_COREDUMP=y` on an nRF54L15 target fails to compile. The Kconfig is exposed (it only `depends on PARTITION_MANAGER_ENABLED...
Hello, one of our devices moved from using the nRF52832 to using the nRF54L15 .
I created new board files and got the old software to run, after some adjustments. The application...
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
I get this error when i try to use FATFS or LittleFS - RAM works though /Users/admin/mass_1/src/main.c: In function 'setup_flash': /opt/nordic/ncs/v2.9.0/nrf/include/flash_map_pm...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
Hi,
I'm running the system_off/ sample on v3.2.3 with these settings in prj.conf
And with this overlay file:
However, I can see that there's a high (and in fact...
Hello, I'm building a multi-image project for an nRF9151: a two-stage bootloader (NSIB + MCUboot) plus two independent non-secure app images.
Each app needs to be able to...
