I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I have a custom board with bl54u and NPM1300 . Working fine.
But now replaced with a NPM1304 as it is pin compatible. Worked fine with fuel gauge NPM1300 on SDK 3.0.1. ...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
Currently, the nRF Connect extensions are available only on the Visual Studio Code Marketplace. We primarily use Cursor, which is a VS Code fork designed for enhanced AI-assisted...
Hello everyone,
I’m currently working on implementing the PK peripheral using Rust with the SVD files for the nRF54L15, but I’m running into a documentation issue.
In...
have a MONOGOTO SIM card that works successfully with TELIT and THALES modems. However, the same SIM card is not detected on the NRF9151-DK. When I send AT+CPIN? , I get:...
Hi I’m having trouble connecting to my nRF5340 dk using nRF Connect for Desktop (Programmer app). When I select the device, I get repeated errors like:
Details:
...
Hello, I’ve been trying to install Nordic Connect SDK 3.1.0 in VS Code, but the installation keeps getting stuck midway and never completes.
I’ve tried several times over...
I'm bringing up a custom board, working through the peripherals one at a time. Unfortunately, I haven't gotten very far before things started misbehaving. One part of the...
With mfw 2.0.2, AT%RAI supports now also "2 – Activate with unsolicited notifications."
That's verfy useful, but I miss some details in the documentation about the usage...
