I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I would like to integrate System OFF mode of operation into idle system hooks in Zephyr (i.e. when the CPU is idle, it goes into OFF power state automatically). As it currently...
Hi there,
I want to advertise to multiple specific BLE addresses, but I don't know how to implement it with the nRF Connect SDK. Please suggest.
I aim to advertise to...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
Hi,
the nrf45L15 datasheet v0.8 says on page 277 "Note: TWIM and TWIS must use clock pins for both SDA and SCL.".
However in the table 72 on page 795, only the SCL pin...
What is the industry best practice for controlling the on/off state of an nrf52 using a momentary push button? Do designers use nrf’s deep sleep mode or properly cut off power...
I've seen many post on the forum about the extension getting stuck at startup. Apparently my issue is a bit different since any of the proposed fix do not work.
While trying...
Hello, I tried the blinky_pwm example on the nrf5340 board and it has worked successfully. I am getting the error when I try to run the pwm code with some modifications Objective...
Hi,
We are integrating the nRF9151 in our app. The %CONEVAL command has a field <tx_power> .
This looks interesting to us, because it can help us estimate our current...
Hi,
I just switched from nRF Connect SDK v2.5.3 to v2.8.0. With the new SDK, I get very many warnings called: implicit conversion from 'float' to 'double' to match other...
Hi,
I am trying to build the nrfx timer example (not modified in any way) in nrf SDK v2.9.0 with toolchain of the same version for the nrf52dk_52832 and I am getting the...
Hi there!
May I know why sample codes cannot be run on nRF54L15DK when board target "nrf54l15dk/nrf54l15/cpuapp" is chosen?
Yet, everything is fine when nrf54l15dk/nrf54l15...
Hello, we have developed a production script with the purpose of programming(with the samd20 dev card) and measuring the power consumption on pcbs with the ppk2. The script...
Hi everyone,
I working on a projetc that i have to use the NVS lib to store several user data on external flash, but i need put FOTA capability in this firmware and when...
Hi everyone, I tried to create BLE ad for customboard nrf54l15, but it doesn't seem to work. I upload my code in the attached file:
when I buil project, I have an error...
