nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,
When I try to run a colleague's project on my PC in debug mode in Visual Studio Code, I get the error "Run to 'main' timed out. Trying to pause program":
The debug...
Hello, guys.
We have nRF51822 SoC with 256KB of Flash and 32KB of RAM memories at our disposal. For our application, we would need to use the BLE stack + over-the-air DFU...
Hello! I recently dived into using the nRF52840 SDK + Zephyr the goal is to use this for Bluetooth Long Range Extended Advertising. Are there available tutorials, resources...
Hello,
I am using sdk12,2.2 and nrf52832. I have interfaced bme680 sensor with nrf52. I am facing strange challenge.
My button interrupt is working every time but it stops...
Hi, I am working on nRF52811 as central and I want to put the device in full power save mode so it does not consume power and activate once I pressed the button. How can I...
Dear Sirs,
I am evaluating the option of controlling a couple of motors (each with an independent controller based on a nRF52840 device) from a Smartphone App. Both controllers...
Hi,
Im using an nRF5340 on the peripheral. Now i would like to use a Dongle on the PC-side, what device can you recommend?
nRF52840 Dongle ? Or is there an other dongle...
Hi, I'm using the serial_lte_modem sample application and I've modified the AT#XMQTTPUB command so that I can specify a slot number from which the device can grab a bank of...
I'm trying to use nrf_delay_ms function inside rtc_handler.
I was wondering if using delay function stops rtc from counting up, so it disrupts rtc interval time.
Hi all,
I´m trying to test the LWM2M Client sample.
After following all the steps explained in this web , when I run it and connect to the DevKit via Putty, I get the...
Hi!
We are debugging low power in our custom board which has several chips (nrff52840, nrf9160, acc, fuelgauge, pmic, etc etc).
We are seeing strange random increases...
Hi,
I have managed to upload the asset tracker via mcuboot to my Actinius Icarus.
It should straight-up connect to the actinius.io cloud, but when I check the link monitor...
Hiii... Team,
I am developing a project based on the nRF52833 with the nRF5 SDK 17.0.2 and Soft Device S140
code is successfully built.. when i try to debug it showing...
my project need to recording audio data from codec continius for more than 10 senconds.i want use nrf5340 to do it.
the codec is tlv320aic3109 or wm8731.I have looked “easydma...
