Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
After reading through the nRF21540 datasheet, I have a few questions.
1. Is section 5.5 saying that even though the spec for VDD is 1.7-3.6V, VDD needs to be between 3.45...
Hello everyone,
I'm now having a problem while using nrfx_spim_xfer on nrf52840. I want to use nrfx_spim_xfer with a callback when transmitting is done.
My setup code...
Hi,
For a development evaluation, I am looking to program nRF52833 to have it interface with "IS25LQ040B" serial flash chip through SPI-1. I found lack of examples and...
I am using the "nRF5_SDK_17.0.2_d674dde" for nRF52 development.
Would like to get the SoftDevice and nRF52 device for confirmation after OTA.
1. When using the sd_ble_version_get...
I am trying to send a OnOff output cluster information to Co-ordinator when a button is pressed in the nrf52840 DK. The problem is the during the initial registration, the...
Hi.
i want to power my nrf52840 with 2 AAA batteries i connected them directly to the module. Is there any Bluetooth signal strength difference when battery voltage drop...
Hello !
I have taken example /examples/crypto/nrf_crypto/aes/aes_ccm
and modify & g_nrf_crypto_aes_ccm_star_128_info instead of ccm
and initialization is failed
...
Hi everyone,
I'm looking for the max output current VDD can source (REG0) when the NRF52833 is configured as High Voltage Mode (see pic for context).
The NRF52840 has...
I need to send bulk data to an MQTT topic on a server hosted by AWS. I'm trying to use datamode option the serial_lte_modem sample but I'm running in to lots of problems....
Hi
I have five custom boards, same batch.
I used one of the boards for developing FW, based on the MQTT simple sample.
The FW uses CA certificates in an h file like...
Hello!
I am evaluating using nrf5340 for a very simple application (literally would only be a few lines of code). In it, I want to pass some information from the network...
Hi,
I am working with a nRF52832 in the nRF52-DK. I am trying to set high logic level of digital outputs to 1.8 V. I have been reading about different operation modes (normal...
Hello, What is the way to send binary or JSON data using AT#XSEND socket command in the new SDKs (>1.60)? Former version of this command contained additional parameter <datatype...
When the phone and controller bonding gets out of sync we are having issues. By out of sync I mean that either the controller (customer board with a nRF52840) or the phone...
