nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello,
I want to use libuarte - advanced UARTE driver in our current application developed for nRF52832 with SDK 17.0.2.
My aim is to merge example libuarte and ble_app_beacon...
Hi!
I want to use my nRF 52840DK as a general purpose BLE demonstrator. I know that this is already possible by using nRF Connect for Desktop, but I'd like to develop a...
Hello,
according my Observation Zephyr, more precisely the rpmsg stuff for BLE between both nRF5340 cores, doesn't work when optimization is switched off. But stepping through...
hello Nordic
i am working with nrf52840 with ncs (on the process of moving to 1.8 currently 'v2.6.99-ncs1-1' )
i have several sensor drivers on my board and flash driver...
hello,
i am using nrf52832 with lis3dh accelarometer and max30205 temperature sensor in our customised board with sdk 15.2 i have included the dfu ota in my firmware my...
hello nordic team I ran the ble_app_uart example in sdk 15.3.0 on nrf52832. When i add printf("\r\n%d\r\n",15); to the code as follows, the program prints 15 to the serial...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a process to set the characteristic and send an indication using sd_ble_gatts_hvx...
Thank you very much for your help. I am currently working on implementing a PWM control function using the nrf52840. I would like to ask you about a build error that occurred...
I need to know in which case the SIW_DET pin is used. Does it depend on the version of the nRF9160 ? Then which versions ?
And is this detection function better in software...
Hello, guys!
I am using nRF51822 SoC with Zephyr. There is a need to configure multiple GPIOs as inputs, with the possibility to fire an interrupt on rising/falling/both...
Hi There,
I am working on a project based on nrf51822. I need to establish pairing the device with smart phone by clicking a button as confirmation on the nrf51822.
...
Hello,
I already fully understand how nRF5340: Network core bootloader working.
As I wondered in the title, I want to move the application firmware data of network core...
The project uses nRF5340. A signal is connected to P0.27/AIN6, and during "normal" mode the pin is used as an ADC.
Before going into sleep mode we would need this pin to...
Hello,
I am working on a project which is based on nrf52840 and Zephyr.
Current prototype uses Adafruit nrf52840 sense board with spi based display attached.
I am new...
Hi,
I experience a very strange issue with UART.
When I try to send data via /dev/ttyACM0 device it looks like the characters sent are buffered and sent only upon the...
