Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
The RTC irq_handler of the latest nRF5 SDK may cause potential problems.
Imagine someone trying to extend the RTC timer from 24bit to 32bit, the developer has to keep an...
Hi All，
The version of Wireshark I used is 3.4.0.
The version of Python I used is 3.6.7.
Packet capture device uses nrf52840 chip.
After installing Wirkshark and related...
I'm working on nrf5340 DK and I wanted to use a mic for sound detection. To do so I installed the X-nucleo-IKS02A1 shield on my board because I have seen that it is compatible...
Hi - I'm using a nRF52840 DK for the first time with my 2010 MacBook pro running OSX Sierra version 10.12.6. I have SEGGER Embedded Studio for ARM 4.12 installed and Segger...
Sometimes, the output of the NRF_LOG commands does not make it to the RTT viewer.
The output of such commands as NRF_LOG_INFO() and NRF_LOG_DEBUG() and NRF_LOG_HEXDUMP_DEBUG...
I design with reference to the evaluation board (nRF9160-DK). What kind of resistor (R4) is used for the input circuit of the GPS antenna? The manufacturer and part number...
Hello,
In the past months, I'm being developing Zigbee Routers-based applications and so far everything is going well.
I've already a few devices installed without OTA...
Hi, looks like I brick my nRF52840-DK board.
It have no any green lights anymore and even do not detected as USB device. The second device I have works well in the same...
Is Thread in nRF Connect SDK developed based on Zephyr RTOS？Do I need to learn Zephyr RTOS to develop Thread using nRF Connect SDK? I just started learning Thread。
Hi,
I am currently evaluating BLE long range feature for one of the our product. for this, using two nRF52840 dongle PCA10059. One used for peripheral and another for central...
Using Zephyr, I'm looking to configure the BLE name of my devices to use the serial number they are provisioned with.
To this end there is the API "bt_set_name" that seems...
Hi,
I have a firmware which need to transit to System-OFF under certain conditions. The startup code of the firmware enables the watchdog timer, which can't be disable...
Hi.
i see that ther are democode in zephyr that use the can shield DFRobot CAN bus V2.0
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.7.1/zephyr/samples/drivers...
Thanks in advance for the help.
I connected my 9160DK (V1.0.1), loaded Asset Tracker V2, etc., and seem to be connected to nrfCloud fine.
I don't seem to ever receive...
