nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi support team,
Our purpose is to provide the modules to our customers. We have developped the hardware module based on nrf52832. Now we want to test the BLE mesh functionalities...
I used VDD channel to detected battery voltage, and the P0.5(AIN3) connect to a LED, But I found that after initialize SAADC, P0.5 cannot control output.
Hi Nordic
I have some questions regarding switch to Application on custom address.
The memory layout in flash is like this:
0x00000000 - MBR 0x00000000 - softdevice...
Hi, I am new to the nRF Connect extension in VS Code and I am having trouble including dealy.h header file to utilize a DelayMs() function. I found the delay.h in the sdk...
I am advertising some data, my hardware is minimum and there are no external interrupts.
1. How do I wake up after entering power save mode with __WFE(); ?
2. I also want...
Hi ,
I want to use above PMIC for Gotek tracker. But I have below questions:
1. Due to the IO limitation, can I use static high or low to configure the chip with VOUTB...
Hello,
We are working on a product that has UART and SPI integrated. We initialise the UART and the SPI at the beginning of the code and everything works fine.
However...
I am using the nRF52840 and the pair of Nordic BLE UART Demo projects ble_app_uart_c_pca10056_s140 and ble_app_uart_pca10056_s140
Please can you tell me how to change the...
Hello all, Currently I am developing a code for a BLE central device that is supposed to receive data from a weight scale (peer). The peer has a service with a custom 128...
Dear friends,
My 52840 DK flashed a serial example(nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial) as a provisioner.
Now, I want to factory reset my provisoner by PyACI...
Good day,
We are trying to interface TCAN4550 to nRF52840 over SPI, and found that sometimes TCAN throws SPI error (underflow of read/write). Looking further, we found that...
Hello all,
I am developing a BLE application with the Softdevices, the peer management module, and with MITM protection.
I've set a bonding static passkey as shown here...
I run a custom multilink BLE service server on nRF9160 DK.
After about 20 minutes of repeated connecting, data exchange and disconnecting from 4 (only four) BLE devices...
Hi,
I need your help to know "How to control RGB LED using PWM in nrf5340?". I have already tried the "RGB_led" sample in NRFconnect SDK v1.5.0
But can't able to control...
Hi
I have nRF52840 DK with nRF5_SDK_17.0.2_d674dde
I am using radio_test example code under examples\peripheral\radio_test:
Radio Channel is fixed at 10,
The data...
