Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
we try to get the NRF52840 to sleep and then wake up from an GPIO interrupt.
We try it in debug mode which should give a emulated sleep mode. So we stop all processing...
Hi,
I would like to enable the APPROTECT readback protection.
What is the advised way to do this when using nrf connect/zephyr? The following line doesn't work (the 'at...
Hi everyone, I'm new to DevZone.
I am writing to ask for info for the first application with BLE.
I need to send data acquired by sensors, RAW mode, via the BLE application...
As far as I know "nRF Connect" DFU function just upgrade one by one,it's too low.
If there is no way to update in batches with DFU,who know a example that DFU function Host...
Hi Devzone:
I would like to shrink heap and stack size to save some RAM space.
I can see in the memory usage page of currently allocated heap and stack:
As you can...
Hello,
I have reserved an area in my flash mapping for settings (0x2000 length). I would like to update it (without application) with DFU / secured bootloader / nRF toolbox...
There is no 'low BLE power' example in the nRFConnect SDK for the nRF5340 - so I am just 'trying thinks' based on documentation I can find to come up with Application/BLE...
Hi.
I want to configure a scene when I create it on a node. So I need to use the Extension field sets, described in the ZCL 3.7.2.4.2.1. I see that the stack has a macro...
Hi Nordic Support Team,
My current setup is : Android Phone <--BLE--> nRF52840 <--LIBUARTE--> External STM32 MCU
I started the example with this folder in the link provided...
The following program will start the TIMER, read the timer value by pressing the button, and set the interrupt event. However, when the interrupt event is timed, the board...
Hai, I am using the sd_power_system_off() function for the deepest sleep mode, and my question what function used to wake up my system
I am using nrf52840 board with 17...
Hello, I need to upload the SEGGER script to FANSTEL EV-BT840 (832)-V4 via nRF52832, but there is something wrong with the connection. In my project, it is needed to use beaconing...
Referenece devzone example, : devzone.nordicsemi.com/.../mesh-mac-address
We should set the new MAC value via sd_ble_gap_addr_set before mesh_init( adv_start)
But flash...
Hi, I am looking to develop some code on NRF53. Looks like only Zephyr is supported. Even the most basic example includes some Zephyr files/libs. Reading the docs it sounds...
