Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I'm working with nRF52840 DK and I want it to advertise iBeacon packets.
I tried the beacon example on ble_peripherals from nRF5_SDK_15.3.0 SDK.
1) nRF connect and...
Hello,
My project is on nrf51822 in which I am using BLE and UART interfaces.
There is single UART available on nRF51822 and I am using it for communication with an...
Hi I am using the custom_ble_service example from https://github.com/bjornspockeli/custom_ble_service_example/blob/master/main.c . The example code will turn a custom characteristic...
HERE is the fix for this problem. It has been reported before (by others) with no reply. I hope that this fix or its equivalent will be incorporated into the next SDK release...
I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then...
Hi Great Support Team:
In the spec of 52832, the rx sensitivity is -96dBm @ 1Mbps.
I'd like to know if the sensitivity is the same (-96dbm) while we adopt ANT+ protocol...
I am using the nrf52840 with freertos and bluetooth (based on the HRM example). Application is designed to sleep for a set period of time before the RTC timer wakes the MCU...
Dear Nordic Team,
Due to a mistake i flashed a bootloader-firmware with the compile flag CONFIG_GPIO_AS_PINRESET onto a custom board where pin P0.21 is tied to ground ....
I just received my nRF9160 DK. I got it connect with the nRF Cloud (with LED 3 and LED 4 blinking). I then started nRF Connect (Programmer) and the application crashed. I...
Hi all,
I want to ask whether I can put the main app on random address in the flash of the chip if there is bootloader and SD present due to future releases of SD and memory...
Hi. My application is scanning ble beacons for 1 sec every minute, and I want to store this data in an array to be sent every 10 min. I am getting the data in BLE_GAP_EVT_ADV_REPORT...
Hi,
I want to implement a Peripheral (GATT Server) that automatically starts notification once a Central connects. No bonding is provided in our system (connection is between...
Hi,
I'm in the early stages of developing a BLE peripheral device that requires the use of the CC310 CryptoCell on an nrf52840-DK board.
I have managed to implement a...
