hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I used nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\spis to test spi,but only the first time can receive data. logs like below,"1234567"
is I send...
static void onoff_state_value_update(app_onoff_server_t * p_server) { /* Requirement: If delay and transition time is zero, current state changes to the target state. */ if...
My app (using S130v2.0.1 nRF51822 SDK12.3) triggers app_error_fault_handler (seen on a PIN; since not able to debug due to timing) on sd_softdevice_disable(). A snippet of...
Hi,
I am using nRF5_SDK_12.3.0 and based on \ble_peripheral\ble_app_uart ( with softdevice of s130) to build my application.
Recently, I tried to add the wdt to my nrf51822...
I adapted the light switch demo of the nRF5 SDK for Mesh for sending a series of reliable on/off messages sequentially from an nRF52840 Preview DK to 20 Thingy:52 servers...
Hi. I have set up a nine node mesh using Thread and the nRF52840 chips. I am using the COAP example. All my nodes are visible and i am able to send pings between them. I am...
Hello I have the dk board and am hoping there is some example or tutorial to help me get started with my project. My goal is to use the nRF52840 as a master to multiple devices...
I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as a peripheral.
The base UUID for this service by default is
{0x9E...
Hello,
First, my setup:
nRF52840 Dongle
Softdevice S140 6.1
SDK 15.2
I built my own adapted application code based on the multilink central example and managed...
I am new to the Nordic chips and for my project I am using an NRF5832 module from Accono. My question is how to get the free SES license for Nordic? When i go to license.segger...
Hello~
I have finished a few easy peripheral project.
Now I tried to understand the structure of central example, ex: ble_hrs_c, ble_nus_c....
I found that services...
When I print too much information ，RTT lost some thing
when I enable the “NRF_LOG_BACKEND_SERIAL_USES_UART”，It is ok
Who tell me Why？ any help will be appreciate！
Hi Nordic,
A problem was found with the SDK15.2 write operation. If the write size is equal to 12000 bytes, the system will return an invalid operation length error.
But...
