Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi All
I have a system with two PCA10040 boards both running with SD version s132_nrf52_6.1.0. The application is build with SDK version 15.2.
I have implemented a peripheral...
hi everyone
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
And I`m using ubuntu via Virtual Box
I refer 'pc-ble-driver' and follow...
Hi,
I am working on developing a consumer product. I need to provide some security to product in the sense that not everyone can connect to the BLE of the product. For example...
Hi All
I have a system with two PCA10040 boards both running with SD version s132_nrf52_6.1.0. The application is build with SDK version 15.2.
I have implemented a peripheral...
I use ble_app_hrs_rscs_relay to build a node which has both central and peripheral roles. I can do scan and adv, but when I add eddystone functions "nrf_ble_es_init(on_es_evt...
Hi,
I want to develop central code to discover services of 3rd party device and to discover their services and read/write characteristics.
As seen many examples from...
Hello,
I am working on NRF52840 DK for a project on Bluetooth Mesh. Using Segger Embedded Studio for Building and debugging.
Basically i am trying to run the examplecode...
I'm writing two 32 bit words. I've verified that the source and destination addresses are word aligned (the UICR address is 0x10001088 and the source address is 2000200C)...
hi.....
i have merged the two programs ble_uart and twi sensor ......in nrf52832 ...segger15.2
i have attached all c files and h files ...... no errors ...when flashing...
Application on NRF52DK running fine average current 2uA. After installing hard and software for the PPK power profiling kit the application draws 8 mA!
Application functions...
Hi guys,
I have a board with STM32 (mbed os) and NRF52832 connected using UART lines.
STM32 has a internet connection and NRF52832 has a bootloader and DFU service.
...
I want to send sensor data from one node to other using access_model_reliable_publish() method, but my data is too large and I'm not able to send large data. What is the maximum...
Hello,
I'm using the TWI example mentioned in the subject line and I'm trying to get the TWI signals out of my demo board (Rigado BMD-350 Evaluation board).
Am I right...
