the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
We are using BMD340 in our project. In our application we need a storage medium for the storing of data. Since our application is an embedded application, we find eMMC...
I am using nRF-Sniffer-v2.0.0.2 beta as seen here: https://www.nordicsemi.com/eng/nordic/Products/nRF-Sniffer/nRF-Sniffer-v2/65225 on a nRF52840 DK.
Wireshark Version: 2...
Hello guys,
I'm having problems with communication between a dwm1001 module (from Decawave) which is a nrf52832 board, and my Raspberry 3 Pi model B.
I have connected...
Hi
According to nRF52840 Product Specification, the SPI master data rate can be set in the SPI frequency register. The configurable values are listed there. Is it possible...
Hello everyone,
Maybe it is a stupid question but I am completely lost,
I have a stm32f103c8tb that I have to use for programming a nrf51822, the thing is I have absolutely...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE.
After pairing, the sum...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE. After pairing, the sum...
Hi
At the company I work for (Ztove ApS) we have expanded the capacity of nrfutil (https://github.com/NordicSemiconductor/pc-nrfutil) to include a option for AES (CBC mode...
Hi
In ESB there is the function nrf_esb_suspend(). After calling it, what function do I call to resume ?
Look forward to hearing from you
Regards
Mahendra
Hello!
Related to the addition of new services to the Attributes table, is there a way to check if a certain service UUID has already been added?
This problem arose because...
How do I check what version I have installed?
The 'Getting Started' page states a minimum version of 9 .5. 0:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
