Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I have read through all the posts I can find on this subject, but none has solved my problem.
- nRF5_SDK_15.1.0
- Example: Segger Embedded Studio Project: twi_master_with_twis_slave_pca10040...
I want to fully understand the use of RTOS in conjunction with the stack. As an example, I took an example ble_app_hrs_freertos (SDK v15.0).
Add a service, for example...
I need to count the pluse number use 51822, the frequency about this pluse is about 0.01Hz to 1Hz and is not fixed, I know use Time1 can achieve this funtion, but the problem...
I wriing softdevice ,aplication and bootloader by nrfprog tool.
But,the device works with the bootloader, not the application.
After writing, it is reset and flag is set...
Hi
I am using fatfs of nRF5_SDK_15.0.0_a53641a. Iam writing a program with keil.
I am trying to save data using SD card now.
By using fatfs example it was possible...
Hello all,
I wanna ask smth related to the use of the nRF52 as a HID keyboard (USB host).
I have already played around with the SDK example ble_app_hids_keyboard and tried...
Hi,
I'm developing a product with the NRF52832.
I have one Blue LED (APA2107LVBC) which is driven directly by a GPIO as shown below :
With a typical Vf of 2.65V, the...
Hi,
I'm trying to implement the following use case:
On the first button push a sensor advertise and bonds with a smartphone. I do it the following way and it works fine...
I tried to configure OTA in my application, but nrf toolbox stucks in "enabling dfu bootloader" and I can see "Starting DFU" showing up really fast, can it be a problem with...
Edit : I solved the problem. The problem was related to variable declaritions and pointer. None of the commands was not working except Write Register and Read Register. I...
Hello. For my application, I have written several functions related to sensor interrogation and work with some periphires of the controller nRF. I split these functions into...
Hi, I started development using a custom board with nRF52840 QIAACO. 1. The prototype uses Holyiot-18010 module ( listed on Nordic 3rd party modules). 2. I am using supply...
Hello. I am using the nRF51 Development Kit which is working well. I am using the examples\ble_peripheral\ble_app_uart sample project as it seems to have the features that...
Hi
I have an external board featuring an nRF52832 connected to the nRF52DK via the Debug Out port on the DK and a 6 pin connector on the external board. I can program the...
