I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
By taking a look at the source code in https://github.com/NordicSemiconductor/pc-nrfconnect-rssi.git, I found the following patch file under fw/src/usbd.patch. It mentions...
We use nRF52840-PDK (PCA10056) with MCU revision Q1AAAA. Given example of secured DFU bootloader (s140) works good. Then we changed MCU on this board to the MCU with Q1AAC0...
Hi to all,
i am working on a project that in it i want use nrf51822 as a peripheral device. i implemented a code but i have a problem, central(cc2540) and peripheral(nrf51822...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
I am trying to migrate a blocking SPI transfer code to a non-blocking SPI Manager schedule call. I have 16 transfers queued up in one transaction.
When I launch it, the...
What is the best way to advertise a custom service and allow BLE connections from a mobile device in a Mesh SDK version 2.0.1 application. Previously I had an application...
Initially I had a project in Mesh 1.0. Everything (provisioning, send&receive) was working fine.
Since upgrade to the Mesh 2.1 there is an issue: provisioning still works...
Hi I've found the documentation around BLE_GAP_TX_POWER_ROLES to be a bit sparse. I was wondering if someone could please give me some more info on them
Three roles have...
I am trying to get the thingy52-mesh-provisioning-demo to work with the SDK for mesh 2.1.1 and nRF5_SDK_15.0.0_a53641a.
I am using the Segger Embedded studio project from...
Hi I'm developing DFU project for my application. I need to have both BLE and UART bootloader. If possible, how can I do that?
Many thanks for the answer
Abele - Ital...
Is there any other way for connecting nRF52 DK with our smart phones, other than through NFC?
My smart phone dosen't have NFC feature and I want to run and test the BLE...
